Free PLC simulator · Write your own ladder · Runs on your phone

Line Sim: find the fault before you swap the part.

A practice machine for maintenance techs. Take a callout: something on it is broken, so find it, fix it and prove it runs. Or pick one of 6 machines (tank, traffic light, garage door, pump + VFD, batch mixer) and write your own ladder logic for it.

  1. 1
    Read the calloutThe operator tells you what's wrong, just like a real call.
  2. 2
    InvestigateWatch the machine, check the PLC lights, and take meter readings.
  3. 3
    Fix & prove itPick the repair, then restart the line. Wrong parts cost you points.
Line Sim PLC workspace
Free run

    Machine

    Short box → GOOD binTall box → pushed into REJECT

    Machine controls

    Press and hold START to run the line. Lock out before you repair anything. Motor 0.0 A

    Start here. A lit light means the PLC sees that signal. Work the machine controls and watch what changes. A light that should be on but isn't is your first clue.

    Inputs (24 VDC)
    Outputs (120 VAC relay)
    Analog inputs (4–20 mA)

    Force (advanced): tap to make the PLC treat a point as ON, then OFF, then normal again. Remember: an output light shows what the PLC wants. It doesn't prove the voltage actually got out.

    Built for the 2 a.m. callout, not the classroom demo

    Most PLC simulators teach you to write a program. On the floor, the program is usually fine. Something in the field changed: a fuse, a loose terminal, a dirty eye, a coil, a bearing. Line Sim trains the skill that gets the line running: reading what the PLC sees, proving where the voltage stops, and fixing only what is actually broken.

    A real PLC scan

    The ladder on screen is the program that runs, so seal-ins, latches, one-shot timers and permissives behave like they do on the floor.

    A meter on the print

    Tap any wire number for voltage to neutral, tap any part for voltage across it, switch to Ω under lockout, clamp the motor amps.

    Faults that act like faults

    Each fault breaks one part. Every symptom you see follows from that: dead inputs, outputs that light but don't fire, permissives that won't make.

    Scored like a real shift

    Time, parts you didn't need, labor minutes, hints and safety strikes all count. Swap-and-pray shows up on the scorecard.

    Write your own program

    A ladder editor built for a phone screen. Contacts, coils, latches, one-shots, TON/TOF/RTO timers, CTU/CTD counters, compares, MOV and math. Download it and the machine runs your logic.

    Analog and an HMI

    A 4–20 mA air-pressure transmitter and a motor current transducer feed real numbers into the PLC. MOV them to N7:0 and N7:1 and they show up on the machine's HMI screen.

    16 auto-graded challenges

    Short lessons from a first rung to a full batch sequence: seal-ins, timers, counters, interlocks, a VFD, pressure control. Tap Check my program and the sim tests it like an instructor. Teams see every technician's progress on the supervisor dashboard.

    Six machines to program

    A conveyor sort cell, a tank fill, a traffic light, a garage door, a pump with a VFD, and a batch mixer. Each has a factory program to study, a beginner version, a bug hunt and a blank page.

    A trend chart

    A meter with a memory. Pick any four signals and watch the last 20 seconds, so a 0.6 s push or a wire that drops out now and then shows up.

    Share a program

    One tap makes a link with your whole program in it. Send it to a classmate or a student, and it opens running in their sim.

    Line Sim vs Factory I/O

    Factory I/O is great software, and if you want a big library of 3D scenes to program against, it is a strong choice. Line Sim lets you program its machine too, but it was built to train troubleshooting, and it runs on a phone. Here is an honest comparison.

    Line Sim (faultline101)Factory I/O
    Runs onAny browser: phone, tablet, PCWindows PC (download)
    Price6 callouts free. All 16, plus every new one, with the full faultline101 trainer (one-time purchase)From about €109 (Starter) to €765 (Ultimate) one-time, or yearly plans
    PLC neededNo. Built-in PLC with live ladder monitorConnects to real or soft PLCs (Starter edition includes a built-in simulator)
    Fault injectionFuses, terminals, coils, PLC output points, sensors, air, mechanicalSensor and actuator "always on / always off" failures
    Electrical print + meterYes: voltage, resistance under lockout, clamp ampsNot a listed feature
    Scored troubleshootingYes: time, wasted parts, hints, safetyNot a listed feature
    3D scenes + scene builder6 machines (2D): sort cell, tank, traffic light, garage door, pump + VFD, batch mixer20+ scenes and a drag-and-drop editor
    Write your own PLC programYes: built-in ladder editor (timers, counters, compare, math, analog), works on a phone, share by linkYes, with an external PLC or its built-in simulator. This is its strength
    Trend chartYes: any 4 signals, last 20 sNot a listed feature

    Factory I/O is a product of Real Games. Feature and pricing details are from factoryio.com as of October 2026 and may change. Read the full comparison.

    Liked the callout? There are 210 more.

    The full faultline101 trainer has 35 modules covering motors, pumps, hydraulics, pneumatics, VFDs, sensors, PLCs and prints. It works offline, and you buy once and own it.

    Try the trainer free

    FAQ

    Do I need a PLC or any software?

    No. The PLC is built in and runs in your browser. It scans the same ladder logic you see on screen. Nothing to install, no license, no hardware.

    Can I write my own ladder logic?

    Yes. Open the Program tab and tap Edit. Tap + to add contacts, coils, timers, counters, compares or math, and tap "Branch around this" to make an OR branch (that is how you build a seal-in). The editor flags mistakes like double coils before you download. Tap Download and the PLC switches to PROGRAM mode, loads your logic and goes back to RUN. Start from one of the example programs if you would rather not start from a blank page. Programming is free; callouts always run the factory program.

    Are there lessons for learning PLC programming?

    Yes. Tap PLC challenges: 16 short lessons, each with a job to program, from your first rung (XIC and OTE) through seal-ins, timers, counters, analog compares, interlocks, a safety beam, a VFD with pressure control, and a full batch sequence. Tap Check my program and the sim works the machine and tells you what passed and what did not. Hints are there if you get stuck. Log in with a free account to save your progress; on a team plan, the supervisor sees every technician's results.

    Which machines can I program?

    Six: the conveyor sort cell (the troubleshooting machine), a tank fill with floats and a level transmitter, a traffic light intersection with a car detector and a walk button, a garage door with limit switches and a safety beam, a pump station with a VFD (an analog speed output) and pressure control, and a batch mixer with a step sequence. Pick one with the Machine buttons above the drawing. Each comes with the factory program, a beginner version, a bug hunt and a blank program.

    Does it really work on a phone?

    Yes, phone first. The machine stays on top and the ladder, I/O, print and repair menu sit in tabs underneath. It also runs on tablets and desktops.

    How is the score worked out?

    You start at 1000. You lose points for time on the callout, every dollar and minute spent on parts that weren't the problem, hints, safety strikes (like ohming a live circuit) and over-fixing (replacing a whole assembly when a cheaper part would do). The callout only closes after the line sorts three boxes clean with every force removed.

    Can instructors use it?

    Yes. In free run, the Repair tab has an instructor panel where you can inject any unlocked fault, including several at once, then hand over the phone. Better yet, put it on a projector and have the class call out the next measurement.

    Is it free?

    6 of the 16 callouts and free run are free, with no account needed. The other 10, and every new callout we add, come with the full faultline101 trainer. If you already own it, log in and they unlock automatically.